<div dir="ltr"><div>Did you use Shift+F1 to record the MSG1.WAV files (it generates multiple ones at different speeds), or were you trying to play pre-recorded .wav files using your own software?  Win-Test message files must be recorded by Win-Test in a specific format and be stored in a specific location based on contest ID and current op.  Note that Win-Test only records message audio using the Windows Default sound card, not the one specified in Interface Configuration.</div><div><br></div><div>The easiest way is to use hardware keying circuits to generate PTT, same as you would for CW, using NPN keying circuits.  The Serial Box (<a href="https://bit.ly/S-BOX" target="_blank">https://bit.ly/S-BOX</a>) provides four of these NPN keying circuits (the second pair can be used with MMTTY for FSK RTTY).  It also includes one or two internal FTDI USB-to-Serial adapters if needed.</div><div><br></div><div>Did you try the Win-Test scripts I published for the FT1000MP?  See <a href="https://bit.ly/wtscripts" target="_blank">https://bit.ly/wtscripts</a> (download FT1000scripts.zip).  The <b>TX.wts</b> and <b>RX.wts</b> scripts may be used in advanced SO2R scenarios to generate PTT by software command instead of keying circuits, so to play Win-Test voice messages, you have to do this:</div><div><br></div><div>#TX $F1 #RX #CLEARRIT</div><div><br></div><div>You have to enable <b>Operating | Technique | Advanced SO2R</b> or else these commands and the scenario is ignored.</div><div><br></div><div>First thing to try is to attempt to play the messages out of the speakers jack to real PC speakers, then connect that jack to the PATCH jack. You should observe the radio being keyed OK. </div><div><br></div><div>FYI, the PATCH jack may not work very well -- it really needs "line level" audio input, not speaker output.  You will probably need an audio isolation transformer between the PC and the PATCH jack to keep hum and noise and RF from getting into the audio.</div><div><br></div><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature">73,<div>Bob, N6TV</div></div></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Aug 6, 2025 at 10:33 AM Michael Ruttenberg <<a href="mailto:mjruttenberg@gmail.com" target="_blank">mjruttenberg@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hi all<div dir="auto"><br></div><div dir="auto">During the IARU contest weekend using an HQ version of WT,L and an FT1000MP, I was <span style="font-family:-apple-system,sans-serif">trying to find a way to get an audio WAV file (for CQ) to be output when I hit F1 and was in SSB mode.</span></div><div dir="auto"><br></div><div dir="auto">I didn’t find a way to get it to play successfully over the air. </div><div dir="auto"><br></div><div dir="auto">I tried editing the LUA scripts to run the following sequence:</div><div dir="auto">Key the PTT</div><div dir="auto">Play the audio</div><div dir="auto">Unkey the PTT</div><div dir="auto"><br></div><div dir="auto">I found some online HEX commands to key the PTT and unkey it.</div><div dir="auto">I found online help to play an audio file. </div><div dir="auto">I could not get it to play nicely together, and it would just click on and off again immediately, without playing the audio while PTT was enabled.</div><div dir="auto"><br></div><div dir="auto">The PC audio was patched into the PATCH port in the back of the rig, and the PTT was controlled over a serial port from the PC. </div><div dir="auto"><br></div><div dir="auto">In theory it was doable. In practice in the heat of battle I could not get it to work. </div><div dir="auto"><br></div><div dir="auto">How do i do this, if I were to try again, without using a MicroHam interface? (I have one at home for just such a job from back when I had a 1000MP, I didn’t think to bring it the 100 miles with me to set it up). </div><div dir="auto"><br></div><div dir="auto">Thanks in advance</div><div dir="auto">Mike</div><div dir="auto">G7TWC</div><div dir="auto"><br></div>
-- <br>
support mailing list<br>
<a href="mailto:support@win-test.com" target="_blank">support@win-test.com</a><br>
<a href="https://lists.win-test.com/cgi-bin/mailman/listinfo/support" rel="noreferrer" target="_blank">https://lists.win-test.com/cgi-bin/mailman/listinfo/support</a><br>
</blockquote></div>