<div class="gmail_quote">On Sat, Feb 5, 2011 at 2:45 PM, Simon Schelkshorn <span dir="ltr"><<a href="mailto:simon@schelkshorn.de">simon@schelkshorn.de</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">

<div id=":83">Problem 1:<br>
As long as Win-Test is NOT started the Microham USB-Device-Router<br>
displays the correct frequency and mode and everything seems to work<br>
as intended. When starting Win-Test it often happens that the Device-<br>
Router shows a totally wrong frequency (e.g. 0.005,32) and also a<br>
wrong mode. In this state you can't do anything useful (e.g. Win-Test<br>
won't send CW because it believes the TRX is set to SSB, even though<br>
it really is set to CW, etc.) Only thing that "solves" the problem is<br>
closing Win-Test. Then the Device-Router immediately shows the<br>
correct status.<br></div></blockquote><div><br>Win-Test manual says:<br><br><b>FT-990</b><br><div style="margin-left: 40px;">COM port set to 4800 bauds, 8 data bits, no parity, no flow control and 2 stop bits.<br>For DTR and RTS, see FT-1000D below. Tnx F6GOX, NX5M.<br>

</div>·<br><b>FT-1000D</b><br><div style="margin-left: 40px;">COM port set to 4800 bauds, 8 data bits, no parity, no flow control and 2 stop bits.<br>When using a powered CAT interface such as the Yaesu FIF-232C CAT interface box and CT-62<br>

cable, set DTR and RTS to Always OFF.<br>When using a "passive" (not powered) interface cable such as the K1NU CAT Control Cable, set<br>DTR to Always OFF, RTS to Always ON. Tnx F5FLN, NX5M, NQ4I.<br></div> </div>

<div><br>What were you using for flow control (DTR and RTS)?  When using microHAM, I think you'll want to set this to Always OFF.<br><br>The symptoms sound like a baud rate or handshaking issues.  Perhaps the FT-990 code in Win-Test has problem.  Instead of selecting radio type FT-990, try setting radio type to OmniRig.  First install OmnRig for free from <a href="http://www.dxatlas.com/omnirig">http://www.dxatlas.com/omnirig</a>, configure it for the FT-990, then start Win-Test. (Note that you must uncheck the radio's virtual COM port in Win-Test to allow OmniRig to take over the CAT functions for Win-Test).  If OmniRig works fine when configured exactly the same as Win-Test re. handshaking protocol and baud rates, then there probably could be a problem with the Win-Test FT-990 code (or the way it talks to the microHAM virtual COM port).<br>

<br></div><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;"><div id=":83">

Problem 2:<br>
When the TRX is set to RTTY, Win-Test assumes it is set to SSB. I<br>
first thought this may be a limitation of the CAT protocol, but as<br>
the Device-Router shows the correct mode it seems to also be a Win-<br>
Test issue.</div></blockquote></div><br>Did you select MODE=RTTY or MIXED in the Contest Configuration screen?  What mode is shown in the logging window?  When using mixed (e.g, for contest type DXpedition), does Ctrl-F1 cycle between radio modes properly?<br>

<br>73,<br>Bob, N6TV<br>