<p><span style="color: rgb(51, 153, 102);">Hello Bob,</span><br />
<br />
<br />
Citando "Bob Wilson, N6TV" <n6tv@arrl.net>:</p>
<blockquote type="cite">Also make sure "Source" is not set to MONO under the MISC tab of MMTTY setup (bad example, <a href="http://docs.win-test.com/wiki/BestPractice1#MMTTY">here</a>).<br />
<br />
<span style="color: rgb(51, 153, 102);">Confirmed, I followed all Win-Test instructions.</span><br />
<br />
<div class="gmail_quote">On Fri, Sep 24, 2010 at 4:37 PM, Bob Wilson, N6TV <span dir="ltr"><<a href="mailto:n6tv@arrl.net">n6tv@arrl.net</a>></span> wrote:<br />
<blockquote style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;" class="gmail_quote">Filipe,<br />
<br />
I don't have enough information, so I can only guess.<br />
<br />
<span style="color: rgb(51, 153, 102);">I am using 2xTS870 and using 2xcable similar to this one (http://www.packetradio.com/catalog/index.php?main_page=product_info&cPath=2&products_id=136)</span><br />
<br />
Make sure the stereo T-adapter is plugged all the way in to the LINE IN jack of the sound card, not MIC. IN.  It is easy to mix them up.  <br />
<br />
<span style="color: rgb(51, 153, 102);">Already checked, it is all the way in and it is in the LINE IN for sure.</span><br />
<br />
Make sure there is no RFI when you connect the common grounds between both Radio 1 and Radio 2 through the T connector. If you are using Elecraft K3, use the LINE OUT jacks not the headphone jacks.  Only use the left (VFO A) channel from each radio.  Ignore VFO B / Sub Rx (right channel).  Turn down the RTTY monitor sidetone in the radio so that when radio 1 transmits, very little audio leaks through to radio 2.<br />
<br />
<span style="color: rgb(51, 153, 102);">I did put ferrites everywhere, even though I will Low Power on this one. <br />
<br />
</span><br />
Connect a heavy braid (coax shield) directly between both radio's ground posts so that any RF stays away from the audio line shield as much as possible.<br />
<br />
Use FSK instead of AFSK.  Make sure the station Mic. is MUTED.<br />
<br />
<span style="color: rgb(51, 153, 102);">I have it set for FSK and not AFSK</span><br />
<br />
Make sure you are starting TWO copies of MMTTY in separate directories.  Each copy of MMTTY must be installed in a <i>separate</i> directory, e.g. Radio1 uses C:\Program Files\MMTTY\MMTTY.EXE and Radio2 uses C:\Program Fiels\MMTTY2\MMTTY.EXE.  See <a target="_blank" href="http://docs.win-test.com/wiki/Menu:Options#RTTY_configuration...">this link</a> for an example.  MMTTY 1 should monitor LEFT channel and MMTTY 2 should monitor RIGHT channel.<br />
<br />
<span style="color: rgb(51, 153, 102);">Exactly as you have, even with those names</span><br />
<br />
Make sure you are not using any of the Advanced SO2R Scenarios that mix up the audio from both radios using $R1R2 etc.<br />
<br />
<span style="color: rgb(51, 153, 102);">Only SO2R is checked, not the advanced</span><br />
<br />
Are you using MK2R+?<br />
<br />
If you still can't figure it out, I would have to see all the screen shots or you would have to install CrossLoop and a broadband connection for debugging the setup remotely.<br />
<br />
<span style="color: rgb(51, 153, 102);">Well thanks for all the tips Bob, I think I will have to go SO1R :(   everytime I TX on second radio, the audio freaks out completelly. the worst is when both MMTTY are receiving the same signal.<br />
<br />
Thanks<br />
Filipe Lopes </span> CT1ILT aka CR6K<br />
<br />
73,<br />
<font color="#888888">Bob, N6TV</font>
<div>
<div> </div>
<div class="h5"><br />
<br />
<div class="gmail_quote">On Fri, Sep 24, 2010 at 4:06 PM,  <span dir="ltr"><<a target="_blank" href="mailto:ct1ilt@sapo.pt">ct1ilt@sapo.pt</a>></span> wrote:<br />
<blockquote style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;" class="gmail_quote"> Hi guys,<br />
<br />
I am trying to setup eveything for WW RTTY to operate SO2R but I am<br />
having an audio issue.<br />
<br />
I have audio from radio 1 into an RCA plug and audio from radio 2 into<br />
another RCA plug then I use a T from 2xRCA to Jack so I have 1 sign to<br />
tip of jack and the other signal to next contact of Jack plug.<br />
<br />
My problem is after TXing for example on Radio 1 the audio will be<br />
mixed up and appear on Both MMTTY windows or one will be with overflow<br />
signal and the other almost no signal.<br />
<br />
I have the Jack plug into LINE-IN port of my sound card SB LIVE 1400!<br />
<br />
I have chosen Left channel for RADIO A and right channel for RADIO B<br />
in MMTTY configs.<br />
<br />
<br />
any idea how to fix this so I have the proper audio on each MMTTY scope?<br />
<br />
Thank you<br />
<br />
Filipe CT1ILT aka CR6K<br />
_______________________________________________<br />
Support mailing list<br />
<a target="_blank" href="mailto:Support@win-test.com">Support@win-test.com</a><br />
<a target="_blank" href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br />
</blockquote></div>
</div>
</div>
</blockquote></div>
<br />
</blockquote>