<div>Bob,</div>
<div> </div>
<div>you are my GURU!!!!</div>
<div>Looks like all working fine!! To give a sure answer I must wait untill end of contest, but it seems ok now!</div>
<div> </div>
<div>I also appreciate Matthias answer, but honestly I prefer to cut off this protocol for this time and maybe try this solution later on during a minor contest :)</div>
<div> </div>
<div>CU on the air and GL in test this week-end.</div>
<div> </div>
<div>73's</div>
<div>Luca<br><br></div>
<div class="gmail_quote">2010/8/12 Bob Wilson, N6TV <span dir="ltr"><<a href="mailto:n6tv@arrl.net">n6tv@arrl.net</a>></span><br>
<blockquote style="BORDER-LEFT: #ccc 1px solid; MARGIN: 0px 0px 0px 0.8ex; PADDING-LEFT: 1ex" class="gmail_quote">You are never forced to use the microHAM control protocol with the MK2R.  Full function is available without it (except for the DVK when you have no parallel cable connected to your PC, but you can use your sound card and the Win-Test internal DVK instead).<br>

<ol>
<li>In the microHAM <b>Router</b> program, go to the <b>SO2R </b>tab</li>
<li>Select <b>Classic Auto Control</b></li>
<li>Define which unused virtual <b>COM port</b> pins you want to use for the three options:  <b>TX Focus</b>, <b>RX Focus</b>, and <b>Stereo Headphones </b>(choose DTR or RTS, for each).<br></li>
<li>If you have the parallel cable connected to your PC, define which pins to use for DVK control</li>
<li>In the Win-Test <b>Interfaces configuration</b> screen, define the same virtual COM ports used in step 3 as <b>Other interface</b></li>
<li>Press the <b>[Configure ...]</b> button</li>
<li>Set DTR / RTS to <b>Active Radio, Headphones control</b>, or <b>Stereo RX Audio</b>, taking care to exactly match what you defined in step 3 in the microHAM SO2R tab.<br></li>
<li>Press <b>[OK]</b></li>
<li>Back at the Win-Test Interfaces configuration screen, <b>uncheck</b> the COM port that says <b>microHam MK2R/MK2R+</b> (this is the most important step)</li>
<li>Press <b>[OK]</b> again and all the delays should be gone.  Win-Test will no longer use the MK2R control protocol for TX / RX switching, it will use virtual COM port pins.  The Advanced SO2R scenarios should work fine.<br>
</li></ol>73,<br>Bob, N6TV<br>
<div class="gmail_quote">
<div>
<div></div>
<div class="h5">On Thu, Aug 12, 2010 at 2:27 PM, Luca NCJ <span dir="ltr"><<a href="mailto:ik2ncj@fastwebnet.it" target="_blank">ik2ncj@fastwebnet.it</a>></span> wrote:<br></div></div>
<blockquote style="BORDER-LEFT: rgb(204,204,204) 1px solid; MARGIN: 0pt 0pt 0pt 0.8ex; PADDING-LEFT: 1ex" class="gmail_quote">
<div>
<div></div>
<div class="h5">
<div>Hi</div>
<div> </div>
<div>Scenario:</div>
<div>WT. dev. 4.6 using SO2R advanced</div>
<div>MK2R with 5.0 firmware and 7.7.1 router.</div>
<div>CW by com ports on both radios</div>
<div> </div>
<div>SO2R scenarios do work well using MK2R standard protocol, but it happens that CW messages start with much delay (abt 2 secs) when the key is pressed.</div>
<div>If I disable the protocol from the com port of WT everything is fine (of course I cannot use anymore scenarios)</div>
<div> </div>
<div>Any suggestion?</div>
<div> </div>
<div>TNX </div>
<div>Luca <a href="mailto:IK2NCJ@D4C" target="_blank">IK2NCJ@D4C</a> (preparing for WAE CW)<br></div><br></div></div>_______________________________________________<br>Support mailing list<br><a href="mailto:Support@win-test.com" target="_blank">Support@win-test.com</a><br>
<a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br><br></blockquote></div><br></blockquote></div><br>