I set up a remote session (VNC) with Neil but was unsuccessful after trying many combinations.<br><br>Jens-Uwe, can you please explain what you mean by a "Splitter from the real prolific port to a virtual"?<br><br>
Neil is using a Prolific USB-to-Serial device with an old device driver "Version 3.0.1.0" dated 2007, under Windows Vista 64. <br><br>In Win-Test we had to change DTR to "Always ON" to supply voltage to the non-standard level converter he is using (not a genuine Icom CT-17). Entering a frequency works and always moves the IC-746 Pro OK, but Alt-F1/Alt-F2 do NOT work (Win-Test changes, but the rig stays put), and Win-Test never tracks movements of the VFO A knob, both when using CI-V Transceive and not using CI-V Transceive.<br>
<br>So I believe the problem is either in his level converter or his USB-to-Serial adapter.<br><br>I went to the Eterlogic site but I'm not sure what I'm a supposed to find there. Why install VSPE when his virtual COM ports are visible to Windows Vista 64 OK already, under Control Panel, Ports?<br>
<br>I went to the Prolific site, but could not figure out which Vista 64 driver is the one to use for his USB-to-Serial converter.<br><br>Neil has two of those converters, one comes up as COM3, and one as COM4, and there are no "real" COM1 or COM2 ports listed. The one on COM3 we set up as PTT on DTR/RTS and it worked fine with Win-Test. The one on COM4 was connected to the IC-746Pro and it only works in a very limited way with Win-Test and his IC-746 Pro.<br>
<br>He is going to try the same hardware with Windows XP to see if the problem is unique to Vista 64. We set up Win-Test to run "As Administrator" in "Windows XP Service Pack 2" compatibility mode, but it didn't help.<br>
<br>73,<br>Bob, N6TV<br><br><div class="gmail_quote">On Thu, Oct 22, 2009 at 2:25 PM, Jens Bremeier [DL2AJB] <span dir="ltr"><<a href="mailto:dl2ajb@gmx.net">dl2ajb@gmx.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Hi Neil,<br>
<br>
the issue of my similar problem was the use of the Virtual Serial Port<br>
Emulator.<br>
I have set up a splitter from the real profilic-port to a virtual (f.e.)<br>
com6.<br>
Wintest use that virtual port with no matter of speed ect.<br>
That solved all my Problems. May this helps you also. Good luck!<br>
<br>
<a href="http://www.eterlogic.com/Products.VSPE.html" target="_blank">http://www.eterlogic.com/Products.VSPE.html</a><br>
<br>
vy 73 de DL2AJB<br>
Jens-Uwe Bremeier<br>
<div><div></div><div class="h5"><br>
----- Original Message -----<br>
From: "Neil Shapiro" <<a href="mailto:neil@neilshapiro.com">neil@neilshapiro.com</a>><br>
To: <<a href="mailto:support@win-test.com">support@win-test.com</a>><br>
Sent: Thursday, October 22, 2009 9:13 PM<br>
Subject: [WT-support] 746 Pro Still Won't Send To WT<br>
<br>
<br>
> Well, I want to thank all for their suggestions and I wish I could<br>
> report success but it is still at the same point. If I type a<br>
> frequency in WT the 746Pro goes to that frequency. But the Radio 1<br>
> dialog box's VFO A field will not reflect any changes at all when I<br>
> rotate the 746's VFO. All parameters are set on the radio as per<br>
> Bob's suggestion -- I did note that transceive I-V was OFF and turned<br>
> it ON. VFO mode and all else is set correct as well. Settings are<br>
> Transceive ON, Poll OFF, DTR ON and RTS OFF at 19,200-8-N-1. (I think<br>
> that having the DTR ON sets power to the USB to serial converter cable<br>
> at least according to HRD's instructions. I know having DTR OFF kills<br>
> even the send to the 746 Pro.) This is crazy because HRD runs here,<br>
> Digipan runs and DMS780 and others. What could be different about WT<br>
> 4.2.0? I have to say I am at my wit's endhere. Any further ideas from<br>
> anyone?<br>
> _______________________________________________<br>
> Support mailing list<br>
> <a href="mailto:Support@win-test.com">Support@win-test.com</a><br>
> <a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
><br>
<br>
_______________________________________________<br>
Support mailing list<br>
<a href="mailto:Support@win-test.com">Support@win-test.com</a><br>
<a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
</div></div></blockquote></div><br>