<div dir="ltr">Hi Bob..I am using 8 1000D's with the FIF232C and no DTR or RTS is necessary with mine de Rick NQ4I<br><br>
<div class="gmail_quote">2008/10/7 Bob Wilson, N6TV <span dir="ltr"><<a href="mailto:n6tv@arrl.net">n6tv@arrl.net</a>></span><br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<div dir="ltr">So are all the FT-1000D users on this list in agreement that if you're using an FT-1000D with Win-Test you <i>must</i> set both RTS and DTR to Handshake? Or is this only true when using 3rd party devices like the <a href="http://k1nu.home.comcast.net/~k1nu/k1nu/Products/control.html" target="_blank">K1NU CAT control cable</a>, and <i>not </i>required when using the original Yaesu <font face="Arial" size="2"><a href="http://www.universal-radio.com/catalog/commrxvr/0322.html" target="_blank">FIF-232C</a> and CT-62 interface cable? I'd like to get this properly documented in the Wiki in the <a href="http://docs.win-test.com/wiki/Supported_rigs" target="_blank">Supported rigs section</a>.<br>
<br>73,<br>Bob, N6TV<br></font><br>
<div class="gmail_quote">On Tue, Oct 7, 2008 at 6:01 AM, Robert Pack, NX5M <span dir="ltr"><<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0pt 0pt 0pt 0.8ex; BORDER-LEFT: rgb(204,204,204) 1px solid">I will test this also to see if it works. Just wish I had found this info<br>sooner. I found a post from over 2 years ago describing the same issues and<br>
the answer given is as follows:<br><><br>I used a FT1000D , my parameters are : 4800 N 2 , you select a port com and<br>you click on the right button ( parameters port ) , you select 4800<br>bits/seconds and bits donnees 8 and no parity and 2 bits stop after you<br>
select DTR and RTS you put handshake. The FT1000D does have the EEPROM V6<br>F4DXW ( TM0HQ 20meters SSB )<br>
<div>
<div></div>
<div><br>----- Original Message -----<br>From: "Mikael Larsmark" <<a href="mailto:mike@sm3wmv.com" target="_blank">mike@sm3wmv.com</a>><br>To: <<a href="mailto:support@win-test.com" target="_blank">support@win-test.com</a>><br>
Sent: Tuesday, October 07, 2008 3:04 AM<br>Subject: Re: [WT-support] FT1000D working<br><br><br>> Does it work if you set RTS to be always high? In that case it's sourced<br>> through those pins as the FT1000D interfaces I have seen.<br>
><br>> And when I read the K1NU page it says "- The RTS (power) pin. My cable<br>> (and many others) gets power from this serial port pin. While most<br>> programs hold this pin high for this reason, keep in mind there is no<br>
> 'industry standard' for this, but the chances are good. Check your<br>> user's manual. In newer programs (2001+) you may have to select an<br>> option to turn this on."<br>><br>> Mike, SM2WMV<br>
><br>> Robert Pack, NX5M wrote:<br>>> The board I am referring to is a small pc board on the DB9 connector.<br>>> This is an interface made by K1NU.<br>>> <a href="http://k1nu.home.comcast.net/~k1nu/k1nu/Products/control.html" target="_blank">http://k1nu.home.comcast.net/~k1nu/k1nu/Products/control.html</a><br>
>> The "guts" are on a small pc board inside the case of the DB9 connector.<br>>> It is one single cable with DB9 on one end and DIN6 on the other and I<br>>> guess you could call it a converter since it replaces Yaesu parts<br>
>> FIF232C and CT-62.<br>>><br>>> ----- Original Message -----<br>>> *From:* Bob Wilson, N6TV <mailto:<a href="mailto:n6tv@arrl.net" target="_blank">n6tv@arrl.net</a>><br>>> *To:* Robert Pack, NX5M <mailto:<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a>><br>
>> *Cc:* Win-Test Reflector <mailto:<a href="mailto:support@win-test.com" target="_blank">support@win-test.com</a>><br>>> *Sent:* Monday, October 06, 2008 9:28 PM<br>>> *Subject:* Re: [WT-support] FT1000D working<br>
>><br>>> On Mon, Oct 6, 2008 at 4:50 PM, Robert Pack, NX5M <<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a><br>>> <mailto:<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a>>> wrote:<br>
>><br>>> I am not sure if they are connected or not in all honesty Bob.<br>>> The board that has the transistors and resistors right behind<br>>> the DB9 connector is quite small and hard to trace and since<br>
>> this is working now I am not even going to bother to try to<br>>> figure it out.<br>>><br>>><br>>> Bob,<br>>><br>>> What board? Inside your PC? What transistors and resistors? Are<br>
>> you using some type of level converter? Isn't it possible to go<br>>> straight from the RS-232 connector on your PC to the CAT connector<br>>> of your FT-1000D, or are you using some type of "converter box" in<br>
>> between?<br>>><br>>> What kind of cable are you using to connect your PC to your<br>>> FT-1000D? Is there any continuity between pins 4 or 7 on the DB9<br>>> connector and /any /PIN on the CAT connector, or the shell? There<br>
>> should be no connection. Pins 4 and 7 should not be grounded, and<br>>> they should not be shorted to each other either.<br>>><br>>> 73,<br>>> Bob, N6TV<br>>><br>>><br>
>> ----- Original Message -----<br>>> *From:* Bob Wilson, N6TV <mailto:<a href="mailto:n6tv@arrl.net" target="_blank">n6tv@arrl.net</a>><br>>> *To:* <a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a> <mailto:<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a>> ; Win-Test<br>
>> Reflector <mailto:<a href="mailto:support@win-test.com" target="_blank">support@win-test.com</a>><br>>> *Sent:* Monday, October 06, 2008 4:20 PM<br>>> *Subject:* Re: [WT-support] FT1000D working<br>
>><br>>> 2008/10/6 Robert Pack, NX5M <<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a><br>>> <mailto:<a href="mailto:nx5m@txcyber.com" target="_blank">nx5m@txcyber.com</a>>><br>
>><br>>> Finally figured out the problem why the FT1000D would not<br>>> track.<br>>> RTS and DTR in the config have to be set to HANDSHAKE.<br>>> Default settings would not work.<br>
>> This is probably the case on the two 990's that I have as<br>>> well and I will check into that first chance I get.<br>>><br>>><br>>> Well done Bob, but I don't really understand why this would make<br>
>> a difference. The DTR (DE-9 pin 4) and RTS (DE-9 pin 7) lines<br>>> are not connected to the 6 PIN CAT connector, are they? Are<br>>> they shorted together?<br>>><br>>> From the FT-1000(D) Operating Manual:<br>
>><br>>> _CAT Connector_<br>>> Pin 1: GND<br>>> Pin 2: SERIAL OUT<br>>> Pin 3: SERIAL IN<br>>> Pin 4: PTT<br>>> Pin 5: S/PO (does anyone know what this means?)<br>
>> Pin 6: NC<br>>><br>>> What version of EPROM is in these radios?<br>>><br>>> From the FT-1000(D) Operating Manual Errata & Addendum:<br>>><br>>> "To improve the versatility of external computer control of the<br>
>> FT-1000, a facility to read back only the current memory number,<br>>> or a 16-byte block of VFO or specified memory parameters has<br>>> been added to EPROM Q5003 on the Control Unit, from revision 6.0.<br>
>><br>>> "The installed EPROM revision number can be non-destructively<br>>> checked by holding the 1 and 3 keys at the upper corners of the<br>>> keypad while switching on. The revision number appears after<br>
>> the display test and manufacturer ID display. If your revision<br>>> is below 6.0, contact your Yaesu dealer for availability and<br>>> price of the upgrade."<br>>><br>
>> Perhaps Win-Test assumes the FT-1000D is at EPROM revsion 6.0 or<br>>> higher, and will not read frequencies accurately if the radio<br>>> has the old original EPROM chips.<br>
>><br>>> 73,<br>>> Bob, N6TV<br>>><br>>><br>>><br>>> ------------------------------------------------------------------------<br>>><br>>> _______________________________________________<br>
>> Support mailing list<br>>> <a href="mailto:Support@win-test.com" target="_blank">Support@win-test.com</a><br>>> <a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
><br>> _______________________________________________<br>> Support mailing list<br>> <a href="mailto:Support@win-test.com" target="_blank">Support@win-test.com</a><br>> <a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
><br><br>_______________________________________________<br>Support mailing list<br><a href="mailto:Support@win-test.com" target="_blank">Support@win-test.com</a><br><a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
</div></div></blockquote></div><br></div><br>_______________________________________________<br>Support mailing list<br><a href="mailto:Support@win-test.com">Support@win-test.com</a><br><a href="http://www.f5mzn.org/cgi-bin/mailman/listinfo/support" target="_blank">http://www.f5mzn.org/cgi-bin/mailman/listinfo/support</a><br>
<br></blockquote></div><br></div>